Uncategorized

Tips On How To Extend Smok Pen Recharge Time


Tips On How To Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was developed by two guys in California. They wished to develop a cool writing instrument that looked like a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the market by storm.

smok pen

The Smok Pen has a built quality that is just great. I found that even though it is an electronic pen the build quality is just as good as any of the pens that I have reviewed. This is due to of how they made the very best cap. You don’t need to be worried about the cap cracking or breaking on you Smok Valve Pen.

Both biggest differences that separate the Smok Valve from other pens may be the form of the coils and just how Element Vape that they are built. Generally the coil on a Smok Pen is larger than on other pens. I think that they did this deliberately, to make the pen feel bigger.

If you take a glance at a Smok Pen, you will notice that your body of the pen is round and not smooth like other pens. On the trunk of the pen there is a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on / off. I must say i liked this feature because it allows me to utilize the Smok Pen 22 whenever I feel like smoking.

To use the Smok Pen you should keep carefully the heat button pressed. Once the button is pressed, the heating element will start to warm up. Once it gets to the appropriate temperature it is possible to switch off the heating element. Smok recommends using a 22mm tank. I prefer a more substantial tank, but that’s just me.

When you put your Smok Pen into the tank you will see a indicator light come on. The indicator light will stay green if you don’t put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids into the coil heads.

After you have completed this step, you should always check to see in case you are at the right temperature for the coils to fire. If not then you should turn the energy off and try again. For anyone who is still not satisfied with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is what I would call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the following two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.

Prior to going any further you should remove the battery from your own pen and unscrew the magnetic cap. You should then take away the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it in to the Smok pen’s electrical port, being careful to not touch any of the coils.

When you have placed the sub-ohm tank in to the pen you need to then place the rest of the components like the wattage, the batteries and the heating element into the included microwaveable microwave oven. Turn on the energy and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it back off. When you first put the pen into the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set then you should follow the on screen instructions.

Once the Smok Pen has reached the temperature that it requires to reach you should then connect the two wires to the negative and positive on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The final step is to connect the positive cable to the bottom of the Smok’s power switch.

After all the components have been placed in to the pen, you should turn the power on. After the first test run, you ought to be able to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you need to take away the battery from the pen and then replace it with a fresh one. For your convenience there is also a green light that can be pressed so as to confirm the battery charging status. Once you have done these things and you also do not see the green light indicating charging, you need to replace the battery.

Close